Auto Logic Automation

Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. Follow these guidelines when you handle the module: • Touch a grounded object to discharge static potential. • Wear an approved wrist-strap grounding device. • Do not touch the bus connector or connector pins. • Do not touch circuit components inside the module. • If available, use a static-safe work station. • When not in use, keep the module in its static-shield box.
Remove power before removing or installing this module. When you remove or install a module with power applied, an electrical arc may occur. An electrical arc can cause personal injury or property damage by: • sending an erroneous signal to your system’s field devices, causing unintended machine motion • causing an explosion in a hazardous environment • causing permanent damage to the module’s circuitry Electrical arcing causes excessive wear to contacts on both the module and its mating connector. Worn contacts may create electrical resistance.
Pollution Degree 2 is an environment where, normally, only non-conductive pollution occurs except that occasionally a temporary conductivity caused by condensation shall be expected. (2) Over Voltage Category II is the load level section of the electrical distribution system. At this level transient voltages are controlled and do not exceed the impulse voltage capability of the product’s insulation. (3) Pollution Degree 2 and Over Voltage Category II are International Electrotechnical Commission (IEC) designations.
Do not remove protective debris strip until after the module and all other equipment near the module is mounted and wiring is complete. Once wiring is complete and the module is free of debris, carefully remove protective debris strip. Failure to remove strip before operating can cause overheating. 

The Remote I/O (RIO) Scanner, 1747-SN, enables communication between an SLC™ processor and remotely located 1746 I/O chassis and other RIO-compatible Allen-Bradley operator interface and control devices. The 1747-SN scanner communicates with remote devices using the A-B Remote I/O link. The RIO link consists of a single master (scanner) and multiple slaves (adapters). Communication between devices occurs over twisted-pair cable with the devices daisy-chained together. Maximum distance for remote communication is 3,048m (10,000 ft.). The scanner is compatible with any standard RIO adapter device. The SLC processor transfers a maximum of 4 logical racks (32 input and 32 output image words) of discrete remote I/O data into the SLC input and output image files. You can adjust the size of the scanner image files during configuration of your SLC system so that the scanner only transfers the discrete I/O data required by your application program. The 1747-SN Series B or later RIO Scanner can be configured to transfer up to 64 words of data to a remote device via block transfer. Refer to publication 1747-6.6, Remote I/O Scanner User Manual, for information on configuration, programming, and block transfers. The SLC 500™ processor (SLC 5/02 or higher) supports multiple scanners in its local I/O chassis. The maximum number is dependent on the following: • backplane power requirements (power supply dependent) • SLC 500 processor I/O data table limit (4,096 input and output bits) • processor memory to supp

1746-NT8 SLC 500 Thermocouple/mV Analog Input Module
Considerations for a Modular System Place your module in any slot of an SLC 500 modular, or modular expansion chassis, except for the left-most slot (slot 0) reserved for the SLC processor or adapter modules. Considerations for a Fixed Controller The power supply in the 2-slot SLC 500 fixed I/O chassis (1746-A2) can support only specific combinations of modules. Make sure the chassis power supply can support the 1746-NT8 and additional module power requirements. Selecting A Chassis Slot Two factors determine where you should install your module in the chassis: ambient temperature and electrical noise. When selecting a slot for your module, try to position your module: • in a chassis close to the bottom of the enclosure (where the air is cooler) • away from modules that generate significant heat, such as the 1746-OA16 or the 1746-IA16 • in a slot away from ac or high-voltage dc modules, hard contact switches, relays, and ac motor drives • away from the chassis power supply (if using a modular system) Remember that in a modular sy

SLC 500 Modular Hardware Style Catalog Numbers 1747-L511, 1747-L514, 1747-L524, 1747-L531, 1747-L532, 1747-L533, 1747-L541, 1747-L542, 1747-L543, 1747-L551, 1747-L552, 1747-L553

Pub. Number Pub. Title Description 1747-SG001 SLC 500 System Overview An overview of the SLC 500 family of products. 1747-IN007 SLC 5/03 and SLC 5/04 Processors Firmware/Operating System Upgrade Installation Instructions Details on the latest operating system upgrade to the SLC 5/03 and SLC 5/04 processors. 1747-IN019 SLC 5/05 Processors Firmware/Operating System ControlFlash Upgrade Installation Instructions Information on the SLC 5/05 ControlFlash upgrade. 1747-RM001 SLC 500 Instruction Set Reference Manual Detailed information on the SLC instruction set. 1761-UM004 Advanced Interface Converter (AIC+) User Manual A description on how to install and connect an AIC+ interface. This manual also contains information on network wiring. 1761-UM005 DeviceNet Interface User Manual Information on how to install, configure, and commission a DNI interface. 1761-UM006 MicroLogix Ethernet Interface User Manual Information on using the 1761-NET-ENI Ethernet interface. 1770-6.5.16 DF1 Protocol and command Set Reference Manual Information on DF1 protocol. GMC-RM001 System Design for Control of Electrical Noise Information on reducing electrical noise. 1770-4.1 Allen-Bradley Programmable controller Grounding and Wiring Guidelines Information on grounding and wiring Allen-Bradley programmable controllers. SGI-1.1 Application Considerations for Solid-state Controls, publication A description of important differences between solid-state programmable controller products and hard-wired electromechanical devices. — National Electrical Code - Published by the National Fire Protection Association of Boston, MA An article on wire sizes and types for grounding electrical equipment. AG-7.1 Allen-Bradley Industrial Automation Glossary

Allen Bradley 1794-AENTR Flex EtherNet/IP Adapter ,Welcome to Auto Logic Automation, your trusted source for cutting-edge industrial automation solutions. As a premier dealer specializing in PLC (Programmable Logic Controller) and VFD (Variable Frequency Drive) products, we provide top-tier technology for enhancing manufacturing processes and optimizing industrial operations. With a commitment to delivering innovative and reliable automation solutions, we cater to the diverse needs of our clients, offering a comprehensive range of high-quality products and expert technical support. Experience seamless integration and efficiency in your industrial processes with our state-of-the-art automation solutions. Partner with us for streamlined operations and unparalleled performance in the realm of industrial automation.

Additional Information:

• Item Code: 248236271
• Production Capacity: 100000000000
• Delivery Time: Ready Stock
• Packaging Details: ROBUST

Additional Information:

• Item Code: 7827835
• Production Capacity: 10000000
• Delivery Time: Ready Stock
• Packaging Details: ROBUST

CompactLogix 5380, Compact GuardLogix 5380, and CompactLogix 5480 Controllers CompactLogix 5380 Controller Catalog Numbers 5069-L306ER, 5069-L306ERM, 5069-L310ER, 5069-L310ERM, 5069-L310ER-NSE, 5069-L320ER, 5069-L320ERM, 5069-L320ERP, 5069-L330ER, 5069-L330ERM, 5069-L340ER, 5069-L340ERM, 5069-L340ERP, 5069-L350ERM, 5069-L380ERM, 5069-L3100ERM CompactLogix 5380 Conformal Coated Catalog Numbers 5069-L310ERMK, 5069-L320ERMK, 5069-L330ERMK, 5069-L350ERMK CompactLogix 5380 Process Controller Catalog Numbers 5069-L320ERP, 5069-L340ERP Compact GuardLogix 5380 SIL 2 Controller Catalog Numbers 5069-L306ERS2, 5069-L306ERMS2, 5069-L310ERS2, 5069-L310ERMS2, 5069-L320ERS2, 5069-L320ERMS2, 5069- L330ERS2, 5069-L330ERMS2, 5069-L340ERS2, 5069-L340ERMS2, 5069-L350ERS2, 5069-L350ERMS2, 5069-L380ERS2, 5069-L380ERMS2, 5069-L3100ERS2, 5069-L3100ERMS2 Compact GuardLogix 5380 SIL 2 Conformal Coated Catalog Numbers 5069-L310ERS2K, 5069-L310ERMS2K, 5069-L320ERS2K, 5069-L320ERMS2K, 5069-L330ERS2K, 5069-L330ERMS2K, 5069-L350ERS2K, 5069-L350ERMS2K Compact GuardLogix 5380 SIL 3 Controller Catalog Numbers 5069-L306ERMS3, 5069-L310ERMS3, 5069-L320ERMS3, 5069-L330ERMS3, 5069-L340ERMS3, 5069-L350ERMS3, 5069-L380ERMS3, 5069-L3100ERMS3 Compact GuardLogix 5380 SIL 3 Conformal Coated Catalog Numbers 5069-L310ERMS3K, 5069-L320ERMS3K, 5069-L330ERMS3K, 5069-L350ERMS3K CompactLogix 5480 Controller Catalog Numbers 5069-L430ERMW, 5069-L450ERMW, 5069-4100ERMW, 5069-L4200ERMW

Flex 16 Point Digital Input Module, Welcome to Auto Logic Automation, your trusted source for cutting-edge industrial automation solutions. As a premier dealer specializing in PLC (Programmable Logic Controller) and VFD (Variable Frequency Drive) products, we provide top-tier technology for enhancing manufacturing processes and optimizing industrial operations. With a commitment to delivering innovative and reliable automation solutions, we cater to the diverse needs of our clients, offering a comprehensive range of high-quality products and expert technical support. Experience seamless integration and efficiency in your industrial processes with our state-of-the-art automation solutions. Partner with us for streamlined operations and unparalleled performance in the realm of industrial automation.

ControlLogix 5580 Controller, Welcome to Auto Logic Automation, your trusted source for cutting-edge industrial automation solutions. As a premier dealer specializing in PLC (Programmable Logic Controller) and VFD (Variable Frequency Drive) products, we provide top-tier technology for enhancing manufacturing processes and optimizing industrial operations. With a commitment to delivering innovative and reliable automation solutions, we cater to the diverse needs of our clients, offering a comprehensive range of high-quality products and expert technical support. Experience seamless integration and efficiency in your industrial processes with our state-of-the-art automation solutions. Partner with us for streamlined operations and unparalleled performance in the realm of industrial automation.

POINT I/O Ethernet Network Adaptor. Class 3 (Explicit Message) requests through the 1734-AENT adapter to a specific POINT I/O module do not always receive a response from the I/O modules. Where an I/O module does not reply to a request, the adapter responds with an error code indicating a timeout

Additional Information:

• Item Code: 11765
• Production Capacity: 10000
• Delivery Time: Ready Stock

onnector type LC-type (fiber-optic)Cable type 8.5/125 µm single-mode fiber-optic cableChannels 1 (transmit and receive fiber)Length, max 10 km (10,000 m, 10,936.13 yd)Transmission 1000 MbpsWavelength 1310 nmSFP transceiver Transceiver Rockwell Automation PN-91972Connector/cable: LC duplex connector, 1000BASE-LX-compliantTemperature, operating 0…60 °C (32…140 °F) -25…70 °C (-13…158 °F)Power from system backplane 1.16 A at 5.1V DC3.4 mA at 24V DC1.16 A at 5.1V DC3.4 mA at 24V DC

ControlLogix 5590 Controllers The ControlLogix 5590 controllers are configurable for standard, safety, redundancy, and Logix SIS applications to help enable faster system performance, capacity, productivity, and security to help meet the growing demands of smart machines and equipment for manufacturing. Working as part of the Integrated Architecture offering, these controllers provide: • Support for Integrated Motion over EtherNet/IP™ for high-speed motion applications. • Support for security, including IEC-62443-4-2 SL 1 certification. • Support for safety solutions. • Support for redundancy solutions. • Support for plant-wide process control. With a ControlLogix 5590 controller, up to SIL 2/PLd (Category 3) can be achieved with one controller using the safety task and safety I/O. ControlLogix 5590 Standard Controller with Safety Partner When used in combination with a ControlLogix 5590 safety partner, a ControlLogix 5590 controller can achieve up to SIL 3/PLe (Category 4). ControlLogix-XT 5590 and ControlLogix-XT 5590 Process controllers provide extended protection in corrosive gas environments.






Catalog Numbers This publication is applicable to these controllers and modules: ControlLogix 5590 Controllers ControlLogix® 5590 Controllers: Throughout Throughout 47, 51 4, 8, 12, 18, 22, 26, 30, 34, 38, 44, 48 1756-L902TS, 1756-L905TS, 1756-L908TS, 1756-L915TS, 1756-L925TS, 1756-L950TS, 1756-L980TS, 1756-L9SP ControlLogix-XT™ 5590 Controllers: 1756-L902TSXT, 1756-L905TSXT, 1756-L908TSXT, 1756-L915TSXT, 1756-L925TSXT, 1756-L950TSXT, 1756-L980TSXT, 1756-L9SPXT ControlLogix-XT 5590 Process Controllers: 1756-L905TPSXT, 1756-L915TPSXT, 1756-L950TPSXT, 1756-L980TPSXT ControlLogix 5580 and GuardLogix 5580 Controllers ControlLogix 5580 Controllers: ControlLogix 5580 Conformal Coated Controllers: ControlLogix-XT 5580 Controllers: 1756-L81E, 1756-L82E, 1756-L83E, 1756-L84E, 1756-L85E 1756-L81EK, 1756-L82EK, 1756-L83EK, 1756-L84EK, 1756-L85EK 1756-L81EXT, 1756-L82EXT, 1756-L83EXT, 1756-L84EXT, 1756-L85EXT ControlLogix 5580 No Stored Energy (NSE) Controllers: 1756-L81E-NSE, 1756-L82E-NSE, 1756-L83E-NSE, 1756-L84E-NSE, 1756-L85E-NSE ControlLogix-XT 5580 NSE Controllers: ControlLogix 5580 Process Controllers: ControlLogix-XT 5580 Process Controllers: GuardLogix® 5580 Controllers: GuardLogix 5580 Conformal Coated Controllers: GuardLogix-XT 5580 Controllers: 1756-L81E-NSEXT, 1756-L82E-NSEXT, 1756-L83E-NSEXT, 1756-L84E-NSEXT, 1756-L85E-NSEXT 1756-L81EP, 1756-L83EP, 1756-L85EP 1756-L81EPXT, 1756-L83EPXT, 1756-L85EPXT 1756-L81ES, 1756-L82ES, 1756-L83ES, 1756-L84ES, 1756-L85ES, 1756-L8SP 1756-L81ESK, 1756-L82ESK, 1756-L83ESK, 1756-L84ESK, 1756-L8SPK 1756-L81EXTS, 1756-L82EXTS, 1756-L83EXTS, 1756-L84EXTS, 1756-L8XTSP 1756-L81ESXT, 1756-L82ESXT, 1756-L83ESXT, 1756-L84ESXT, 1756-L8SPXT ControlLogix 5570 and GuardLogix 5570 Controllers ControlLogix 5570 Controllers: ControlLogix 5570 Conformal Coated Controllers: ControlLogix-XT 5570 Controllers: GuardLogix 5570 Controllers: GuardLogix 5570 Conformal Coated Controllers: GuardLogix-XT 5570 Controllers: Armor™ ControlLogix 5570 Controllers: Armor™ GuardLogix® 5570 Controllers: Controller Redundancy ControlLogix Redundancy Modules: 1756-L71, 1756-L72, 1756-L73, 1756-L74, 1756-L75 1756-L71K, 1756-L72K, 1756-L73K, 1756-L74K, 1756-L75K 1756-L73XT 1756-L71S, 1756-L72S, 1756-L73S, 1756-L7SP 1756-L71SK, 1756-L72SK, 1756-L73SK, 1756-L7SPK 1756-L73SXT, 1756-L7SPXT 1756-L72EROM, 1756-L73EROM 1756-L72EROMS, 1756-L73EROMS 1756-RM3, 1756-RM3-2SFP, 1756-RM3XT 1756-RM2, 1756-RM2K, 1756-RM2XT

1766-L32BwaMicroLogix 1400 32 Point Controller
The 1769-L33ERC Allen Bradley is a conformal-coated CompactLogix 5370 L3 controller designed for harsh environments, featuring 2MB of user memory, dual Ethernet/IP ports with DLR capability, and support for up to 16 expansion modules. It offers robust performance with built-in motion control capabilities and 1GB SD card storage. 

POINT I/O 5V DC and 24V DC Very High Speed Counter Module Catalog Numbers 1734-VHSC5, 1734-VHSC24, 1734-VHSC24K, Series C

The following POINT I/O modules are referred to in this publication: • 1734-VHSC5, Series C, POINT I/O 5V DC very high-speed counter module • 1734-VHSC24, 1734-VHSC24K, Series C, POINT I/O 24V DC very high-speed counter module The VHSC is a two-module set: • Module 1 houses the VHSC functionality. • Module 2 provides screw terminals necessary to access chassis ground (chas gnd) and common (C). - Module 2 connects screws 4 and 5 and screws 6 and 7 for ease of wiring power to the input device. - Module 2 is not necessary for VHSC functionality. - Module 2 serves only to ease customer wiring. - Module 2 does not use a node address or consume power from the POINTBus™. Mount module 2 adjacent to module 1. Note that this POINT I/O series C product can be used with the following: • DeviceNet® and PROFIBUS adapters • ControlNet® and EtherNet/IP™ adapters, using Studio 5000 Logix Designer® application version 20 or higher

Flex EtherNet/IP Adaptor,Welcome to Auto Logic Automation, your trusted source for cutting-edge industrial automation solutions. As a premier dealer specializing in PLC (Programmable Logic Controller) and VFD (Variable Frequency Drive) products, we provide top-tier technology for enhancing manufacturing processes and optimizing industrial operations. With a commitment to delivering innovative and reliable automation solutions, we cater to the diverse needs of our clients, offering a comprehensive range of high-quality products and expert technical support. Experience seamless integration and efficiency in your industrial processes with our state-of-the-art automation solutions. Partner with us for streamlined operations and unparalleled performance in the realm of industrial automation.

Additional Information:

• Item Code: 2378912739812AVGD
• Production Capacity: 1000000000000
• Delivery Time: READY STOCK
• Packaging Details: ROBUST